技術參數 Technical Parameters
【產品詳情圖片】
容 器 類 別 Tank Type：Ⅱ類
介質 Medium：LCO2
設 計 壓 力 Design Pressure: 2.2MPa
允許工作壓力Max. Allowance working pressure: 2.27MPa
容 積 Volume ：10.5m3
材料Materials：
內膽Liner：16MnDR
外膽 Shell：Q345R
規格Specifications：
內膽 Liner：φ1600×8/8
外膽 Shell：φ2100×8/8
總重 Weight：7600kg
夾層保溫材料Sandwich insulation material:
CEP60型珠光砂（含水量≤0.3%） CEP60 pearl sand (water content ≤0.3%)
內膽氣壓試驗 Liner pressure test：
介質 Medium：氮?dú)? Nitrogen 試驗壓力 test pressure：2.61MPa
內膽內管材料Liner tube materials：S30408
閥門 Valve：低溫不銹鋼三段式球閥 cryogenic stainless steel three stage ball valve
制造驗收標準 manufacturing accept standards：
According to GB/T 18442-2011 Stationary vacuum insulated cryogenic pressure vessel
TSG 21-2016 Safety technical supervision procedures for fixed pressure vessels
【產品詳情圖片】
【變量3】【變量2】【變量1】

結構說明 Structure Description
1. 泄放裝置 Discharge device
2. 內膽 Liner
3.保溫層(珠光砂) Insulation (pear sand)
4.外殼 Shell
5.儀表(差壓計、氧壓表、組合閥) Meter (differential pressure gauge, oxygen pressure gauge, combination valve)
6.抽空口及真空閥門Evacuation port and vacuum valve
7.管路閥門 Pipeline Valve
說 明Description:
⑴本儲罐的操作系統多集中于儲罐底部，儀表系統及組合閥設置在筒壁，便于觀察操作.
The operating system of the tank and more concentrated in the bottom of the tank, instrument system and valve combination set in the cylinder wall, easy to observe the operation.
(2) 內膽設置有兩個安全閥S1、S2，夾層泄壓裝置B。
There are two safety valves S1, S2 inside the liner, sandwich pressure relief device B.
(3) 連接形式：進液口→2＂螺紋連接，排液閥→2＂螺紋連接，抽空口→法蘭.
Connection: inlet → 2 "thread connection, drain valve → 2" thread connection, exhaust port → flange.
【產品詳情圖片】
【變量3】【變量2】【變量1】

儲罐的增壓 Tank pressurization
【產品詳情圖片】
當儲罐向外供液又需要穩定排液壓力時，可利用汽化器（另外配備）進行增壓。其操作過程如下：
The carburetor (available separately) can be used for boosting when the reservoir is supplied externally and requires stable discharge pressure. The operation is as follows:
2.3.1開啟V2排液閥，使液體二氧化碳汽化器汽化，開啟V3回氣閥（根據用戶回氣管路的設置，V3回氣閥可置于常開狀態）從汽化器分流出來的氣體返回儲罐上部，使儲罐內增壓。
Open the V2 drain valve to vaporize the liquid carbon dioxide vaporizer and open the V3 return valve (the V3 return valve can be normally open depending on the return air line of the user). The gas diverted from the vaporizer returns to the upper part of the tank , So that the pressure tank.
2.3.2當儲罐內壓力達到2.1Mpa時，可暫時關閉V3回氣閥。
When the tank pressure reaches 2.1Mpa, the valve can be temporarily closed V3 return gas valve.
2.3.3排液過程中，可通過控制V3回氣閥的開度，使增壓能力維持在壓力穩定的水平。
During drainage, the degree of pressurization can be maintained at a pressure-stable level by controlling the opening of the V3 return valve.
【產品詳情圖片】

2 儲罐的操作Tank operation
【產品詳情圖片】
儲罐的操作分為充液、貯存、增壓、排液等過程，每個過程必須做到：V6三通截止閥（連接安全閥）和V8液位計組合閥始終處于全開狀態。罐內壓力不應高于2.16Mpa，壓力不應低于0.8Mpa .
The operation of the tank is divided into filling, storage, pressurization, drainage and other processes, each process must be: V6 three-way valve (connecting safety valve) and V8 level gauge combination valve is always in the fully open state. Tank maximum pressure should not exceed 2.16Mpa, the minimum pressure should not be less than 0.8Mpa.
【產品詳情圖片】
【主變量】【變量3】【變量2】【變量1】

http://www.shemalestube.net