【標題】
【主變量】【變量1】
【產品詳情圖片】
低溫儲罐是我公司七大事業中心之一---深冷容器事業中心主要產品，具有有5-200立方米立、臥式低溫液體儲罐（液化天然氣儲罐LNFG，液氧儲罐LO2，液氮儲罐LN2，液氬儲罐LAr2，二氧化碳儲罐LCO2）。
低溫儲罐是貯存低溫液化天然氣、液氧、液氮、液氬、液態二氧化碳等介質的貯存壓力容器。低溫儲罐為雙層固定真空粉末絕熱儲罐（貯槽）。液化天然氣、液氧、液氮、液氬內膽原料選用不銹鋼，二氧化碳儲罐為16MnDR），外膽原料為Q345R或許16MnR。外表防腐涂層選用噴砂除銹、吹掃、噴涂等工藝，同時選用了挪威進口佐敦涂料，保證5年油漆不脫落。
【產品詳情圖片】
低溫儲罐在內容器與外容器之間的夾層選用熱態下的珠光砂為絕熱材料并抽真空，以到達的絕熱作用。
低溫儲罐產品主要用于液化天然氣、液氧、液氮、液氬以及二氧化碳等氣體的低溫液態存儲。1立方米液體能夠代替130支氣體鋼瓶。它能夠替代每天用氣瓶往返運輸，節約很多的人力物力。
【產品詳情圖片】
【變量3】【變量1】

充液的操作 filling operation
【標題】
充液分為充液和補充充液。
充液的操作如下：
Filling fluid is divided into the first filling and filling fluid.
The first filling operation is as follows:
2.1.1 儲罐吹除置換干凈達到要求后，將充液管線與儲罐的充液接頭連接，液位計組合閥處于平衡狀態準備充液。
After the tank blows off to replace the cleanliness meets the requirements, the filling liquid line is connected with the liquid filling joint of the tank, and the liquid level gauge combination valve is in an equilibrium state to be filled.
2.1.2充入與液體二氧化碳純度相同的氣體，使罐內壓力達到0.8 Mpa以上，方可進行充液。 filled with the same purity of liquid carbon dioxide gas, the tank pressure reached 0.8 Mpa above, before filling.
2.1.3 將充液管線接通槽車，先開啟V5殘液閥，排出管線內的雜質氣體后，再開啟V1進液閥和V7排氣閥，V8液位計組合閥處于全開狀態，顯示液位計讀數進行充液。
The filling liquid line connected tanker, first open the V5 raffinate valve, exhaust gas impurities within the pipeline, and then open the V1 inlet valve and V7 exhaust valve, V8 level gauge combination valve is fully open state, Display level meter readings are filled.
2.1.4 在充液過程中，當液位計指示液位接近標定值時，可間斷開啟V4充滿指示閥，如有液體噴出，應立即停止充液，關閉V4充滿指示閥。
During the filling process, when the liquid level gauge indicates the liquid level approaches the calibration value, the V4 may be intermittently opened to indicate the valve. If any liquid is ejected, liquid filling should be stopped immediately and the V4 valve should be closed.
2.1.5關閉V1進液閥和V7排氣閥，打開V5殘液閥，拆下充液管線，充液結束。
補充充液的操作與充液的操作方法相似，不同點是補充充液時一開始就可以大量充液。
Close the V1 inlet valve and the V7 exhaust valve, open the V5 residual valve, remove the filling line, and fill with liquid.
The procedure for replenishing the priming solution is the same as for the first priming procedure, except that the priming solution can be replenished extensively from the beginning.
【產品詳情圖片】
【標題】

液體的排放 liquid discharge
【產品詳情圖片】
2.4.1液體二氧化碳的正常排放是在儲罐增壓后，開啟V2排液閥，V3回氣閥，液體二氧化碳便流入汽化器汽化，供使用點使用。
The normal discharge of liquid carbon dioxide is after pressurization of the tank, open the V2 drain valve, V3 return valve, the liquid carbon dioxide will flow into the vaporizer vaporization for use point.
2.4.2為滿足排液過程的穩定壓力，應按“儲罐的增壓”操作方法進行增壓。
In order to meet the steady pressure of the drainage process, it should be pressurized according to the method of "pressurized tank".
【產品詳情圖片】
【標題】

液體的儲存 liquid storage
液體二氧化碳的儲存屬于帶壓（壓力不低于0.8Mpa）儲存。儲存期間除壓力表、液位計、安全閥應投入使用外，其他閥門應處于關閉狀態。當儲罐壓力超過2.1Mpa時，開啟V7排氣閥降壓。但應注意：內罐的壓力不得降至低于0.8Mpa，否則將引起液體二氧化碳轉變?yōu)楦杀?br>Liquid carbon dioxide storage with pressure (pressure not less than 0.8Mpa) storage. During the storage, the pressure gauge,level gauge, safety valve should be put into use, the other valves should be closed. When the tank pressure exceeds 2.1Mpa, open the V7 exhaust valve buck. However, it should be noted that the pressure inside the tank must not drop below 0.8Mpa, otherwise liquid carbon dioxide will be converted to dry ice.
【產品詳情圖片】
【標題】

http://www.shemalestube.net